The worn-out seat on associate editor Landon Hall’s 1973 Yamaha TX650.
The first step is removing any seat hardware. For our Yamaha that meant removing the bolts securing the grab strap, the front and rear hinge plates and the seat lock tongue. Take pictures, and mark and bag the parts so you know where they go.
The Yamaha’s seat cover is secured by metal barbs in the seat pan. Removing the cover is simply a matter of stretching the fabric back and off the barbs. At this point we were simply checking the fabric’s strength.
Before the cover can come off you have to remove the aluminum trim strip running around the seat. It’s held in place by eight small nails secured by spring clips, which are easy to pry off with a screwdriver.
Spring clips removed, gently pull the trim strip off the seat. Don’t worry if you damage the clips, you can find new ones at most hardware stores. Don’t lose any of the nails, they’re unique. Mark the nail hole locations on the seat pan with chalk. We forgot, costing us time later.
Now you can start getting down to business removing the seat cover. We found it was easiest starting at the back; releasing the fabric’s tension here loosened up the cover.
Working our way around from the back, we gently pried the metal tabs up 90 degrees to make it easier to get the fabric off. Be careful, as rusted tabs will tend to break.
Once the cover’s been freed from the tabs, gently pull it away from the base, starting at the bottom. Go slowly, as the old foam often sticks to the fabric.
Once the cover’s released from the bottom edges, it should basically fall off. It looks even worse removed than it did in place!
Our seat had already lost a sizeable chunk of the foam core where the seat had torn the worst. To repair it, we first cut out the surrounding area to make a defined notch in the seat foam.
Next, we took some upholstery foam and cut out a similarly shaped but slightly oversized piece. The new cover will even it out. Using 3M Hi-Strength 90 Spray Adhesive, we then glued the foam patch in place.
At this point we were ready to install our new cover, but first we worked our way around the seat pan one more time to make sure all the metal barbs were pulled up to where the fabric would easily clip on.
After gently heating the cover with a hair dryer, we placed it over the old foam and centered it. Turning the seat over, we started at the back, making sure the cover stayed centered and that we liked how the fabric was sitting, then clipped it onto four of the barbs.
With the cover secured at the back and the metal tabs pushed down flat, we moved toward the front of the seat, making sure the cover was still centered and clipping it in place about a quarter of the way back from the front. Saddlemen recommends securing it closer to the center, but we opted to move forward because of how our seat pan bulges out in the middle.
Using the hair dryer to warm the fabric so it would stretch easily, we then pulled the cover toward the front and clipped it onto the tabs at the center of the pan, then worked our way to the edges.
Next, we worked back along both sides, using the hair dryer to aid stretching and checking to ensure we were centered as we stretched the fabric over the pan. We did this slowly and carefully, making sure we had a nice, even pull on the fabric. Once we were happy with how it fit, we folded the metal tabs flat.
WIth the cover on, use an awl to push through the fabric where the studs for the trim piece go through. We forgot to mark the nail hole locations with chalk (see #4) and had to refer to photos to find them.
One of the nails that holds the trim, along with an old speed clip on the left and a new one on the right. New clips were only $0.26 each at the local hardware store.
Install the nails onto the trim. Gently position the trim piece in place on the seat and push the nails through their holes. Check that the trim piece is correctly located, then push the nails in and clip them in place with the speed clips.
That’s it! Work your way around the seat a couple of times to ensure the speed clips are secure and the metal tabs are folded down, and you’re done. Looks pretty good, eh?