Tech Corner

Technical Q and A for classic motorcycle maintenance and repair.

Add to My MSN

Fouled Spark Plugs

11/29/2011 2:34:59 PM

Tags:

 Keith 

Editor's note: If you’re having trouble with that old Suzuki, BSA or BMW, Keith Fellenstein is your guy. From motorcycle tuning tips to detailed motorcycle engine repair, he can draw from a wealth of experience to help guide you to success. Send questions to: Keith’s Garage, 1503 SW 42nd St., Topeka, KS 66609, or send an e-mail with "Keith's Garage" as your subject.   

Fouled spark plugs 

Q: My 1973 Norton 850 Commando has the annoying habit of fouling spark plugs. What can I do to prevent it?
-Kenneth Peters/Lawrence, Kan. 

A: If this is the first time you’ve fouled a set of plugs, I’d change to projected tip spark plugs of the same heat range and try again. Projected tip plugs have the same thread depth as regular plugs, but the center electrode projects farther out into the combustion chamber. Not far enough to collide with the valves or piston, but out in the fire a little more than a regular plug. Sometimes that’s all it takes to stop fouling plugs. If that doesn’t work, you may want to try one heat range hotter plug.

Finding out why the plug is fouling is also a good idea. Is the fouled plug sooty dry black, indicating a too rich condition, or sooty wet black, indicating oil in the combustion chamber? Sooty dry black can be remedied by adjusting the carburetors to lean out the mixture as needed. You’ll need to determine where in the power band the fouling is taking place; idle, just off idle, mid-range or wide open.

Each area of the power band is controlled by a different part of the carburetor circuit. Idle is controlled by the idle jet and the air screw. On Amal Concentric carburetors like you should have, you screw the air screw in until it lightly seats, then back it out one and one-half turns. That’s your starting point. Continuing to turn the screw counterclockwise leans out the mixture by admitting more air into the idle circuit. Your goal is the smoothest idle with no stumble as it transitions from idle to just open. If you have a smooth idle, but the bike hesitates just as you open the throttle, turn the air screw clockwise one-quarter to one-half turn to provide just a little more gas for acceleration.

The second circuit to adjust is wide open. Find a good straight road with a slight incline and light traffic and open the throttle up in third gear. Does the bike accelerate smoothly or does it stumble or surge? If it doesn’t accelerate smoothly, does slightly closing the throttle improve the running? If slightly closing the throttle improves running, your main jet is too small. Go up by 10 to the next largest main jet and repeat. Reading the plugs by doing a plug chop will also tell you about your mixture. Repeat the test above, using the kill button to stop the engine about two-thirds of the way up and coast to a stop. Remove the spark plugs and see what color the center electrode shows. Dry sooty black is too rich, stark white is too lean, tan to chocolate brown is just right.

After you have both the idle and wide open settled down, you can then work on just off idle and mid-range. Just off idle is controlled by the cutaway of the slide.

Amal expresses the cutaway in numbers like “3” or “3½.” The higher the number the leaner the mixture. Mid-range is controlled by the needle in the slide; raise the needle to richen the mixture, lower it to lean the mixture. Repeating the plug chop as mentioned above will tell you what you need to do. It’s a long, tedious process, but the end result is a bike that responds as it should through its full rpm range.

It can be harder to find the cause of oil in the combustion chamber, although there are really only a few sources; worn rings or worn valve guides, and possibly leaky or torn valve seals on the intake valves. A compression check and leak down test can sometimes give you an answer without taking the head off. You can also remove the carburetors and intakes and look in the intake to see if oil is visible on the intake valve or guide. There’s usually not a problem with the exhaust valve as that side runs pressurized while the intake has a vacuum, trying to suck oil down from the valve train. MC 

 



Related Content

High-Mileage Classics: 200,000-mile 1973 Norton 850 Commando

Stan Keyes shares the experience of racking up more than 200,000 miles on a 1973 Norton 850 Commando...

Amal Carburetor Concerns in a 1970 Triumph Bonneville

Motorcycle Classics tech expert Keith Fellenstein solves an Amal carburetor problem in a 1970 Triump...

Triumph Bonneville Carburetors

Motorcycle Classics’ tech expert Keith Fellenstein answers the question of which carburetors to use ...

1970 Triumph Bonneville Boyer Ignition Troubles

Motorcycle Classics tech expert Keith Fellenstein solves more Boyer ignition troubles, this time on ...

Content Tools




Post a comment below.

 



The sound and the fury: celebrate the machines that changed the world!
First Name: *
Last Name: *
Address: *
City: *
State/Province: *
Zip/Postal Code:*
Country:
Email:*
(* indicates a required item)
Canadian subs: 1 year, (includes postage & GST). Foreign subs: 1 year, . U.S. funds.
Canadian Subscribers - Click Here
Non US and Canadian Subscribers - Click Here
 

Motorcycle Classics is America's premier magazine for collectors and enthusiasts, dreamers and restorers, newcomers and life long motorheads who love the sound and the beauty of classic bikes. Every issue  delivers exciting and evocative articles and photographs of the most brilliant, unusual and popular motorcycles ever made!

Save Even More Money with our RALLY-RATE plan!

Pay now with a credit card and take advantage of our RALLY-RATE automatic renewal savings plan. You save an additional $4.95 and get 6 issues of Motorcycle Classics for only $24.95 (USA only).

Or, Bill Me Later and I'll pay just $29.95 for a one year subscription!