Brake Arcing Service by Race Tech

Before sending my wheel off for service, I checked it against Race Tech’s requirements. First up was inspecting for any loose spokes; they must be properly tensioned and the wheel must run straight and true. Re-tensioning the wheel after machining runs the risk of pulling the drum out of shape, negating any improvements. Next was thoroughly cleaning the brake backing plate before installing new shoes (you can use your old ones if they’re good, but why would you?) and making sure the brake cams were properly lubed. Following that I inspected both wheel bearings (if they’re old or suspect, replace them), then I confirmed the wheel axle was straight before shipping the wheel — complete with brake backing plate and axle — to Race Tech in Corona, California.

Black lines act as cutting guide; when they’re gone, the drum’s done.Photo courtesy Race Tech

Getting true

At Race Tech, the wheel is set in a work stand supported by its axle. The inside face of the drum is then marked with black squiggly lines. Next, a specially made cutting tool designed by Race Tech founder Paul Thede is centered on the wheel axle. An air-powered rotary cutting head attached to the tool is adjusted to just touch the drum face. As the cutting head spins, the tool slowly revolves around the drum, the cutter removing metal as it does. The black squiggles act as a guide, showing high spots as material is removed; wherever black still shows, the drum hasn’t been cut. This is done in multiple passes, the cutter removing as little material as possible with each pass until a clean surface remains.

The shoes are cut next. In this step, the shoes — complete with backing plate — are held in place while another rotary cutter, set up to exactly duplicate the arc and diameter of the cut on the drum, matches the cut to the shoes, ensuring the shoes are exactly concentric to the drum. Simple in concept, it takes the right tools and skill to do it correctly.

Ten days after sending it out, my wheel was back and ready for installation, but not before draining the forks and refilling them with fresh 15 weight fork oil. Finally, I slipped new fork gaiters in place before reinstalling the forks and bolting the wheel back up.

I knew when I started that the original brake cable was stretched almost to the limit, so I turned to Barnett Clutches & Cables for a replacement. Barnett can custom make cables for just about any application, and less than a week after relaying the necessary specs to Ivan at Barnett a new cable showed up in the mail.

With the new cable installed, it was time to adjust the brakes. A twin-leading-shoe design, the BMW setup needs to be properly adjusted to work well. First, the brake arms need to be correctly oriented: If you remove them, mark them first to make sure they go back in their original position. Next, tension the brake cable until the rear shoe just touches the drum. Pull the brake lever; the rear shoe should touch the drum first, followed almost immediately by the front. The front shoe is adjusted with the brake shoe stop, located just behind the forward brake arm on the brake backing plate. To adjust tighter, hold the brake stop with a 5mm Allen wrench and loosen the 13mm lock nut. Pull lightly on the brake lever and turn the stop with the Allen wrench until you can feel it hitting against the brake inside the backing plate. Turn it back slightly, lock it in place, then check the pull of both arms when squeezing the lever. It takes a bit of fiddling, moving the stop in and out, but what you’re looking for is an even pull between the front and rear arms, with the rear making initial contact, followed immediately by the front.

Brake backing plate with shoes jigged up on Race Tech’s brake arcing tool to cut and match the profile of the shoes to the drum.Photo courtesy Race Tech

Brakes away

With everything back together I made several runs up and down a low-traffic road, running up to speed before hitting the brakes hard to heat them up, followed by a rest to let them cool, repeating this several times to bed the new brake shoes to the freshly machined drum. The result? Wow. The new cable and proper adjustment were a big help, no question, but the front brakes, previously feeble at best, now bite with authority, pulling the BMW down from speed with confidence. The pull on the lever is firm, and the small amount of “chatter” I used to get with a really firm tug on the lever is completely gone.

So what price performance? Race Tech charges $200-$225 for the service, with shipping extra. New Ferodo shoes set me back $77. Add $34.60 for the cable and the total was around $335. Given the return — properly working brakes I can count on — if you’re actually riding your classic, I’d call this one of the smartest performance upgrades you can make. — Richard Backus